All Metal Digital MFC / MFM MODEL EX-550 SERIES

Update Terakhir

01 / 12 / 2019

Min. Pembelian

1 Buah

Dilihat Sebanyak

6 kali

Harga

CALL

PT. Wiratama Mitra Abadi experienced in the fie

I. Supply of engineering products such as flow meter, Connector Nanaboshi, Connector Daiwa Dengyo, Connector SIBAS, Connector HartingFlowmeter, Hydraulic Parts , Oil Skimmer, Liquid Flow Meter, Linning clutch, Flow Sensor, MAG, MICRO SENSOR, Lubricating Pump, Flow Control, Portable Flow Meter, Heavy Duty Connector, Gas analyzer, Hydraulic Seal, Pneumatic parts, Tacho geerator, hubner, Cylinder, Seal Kit, Level control, Reflex Sensor, UPS, Spiral Bavel Gear, FLOWMETER, Clutch and Brake, Cara Kerja Flow Meter, Belt Skimmer, Steam Flow Meter, Gas Flow Sensor, electromagnetic, magmeter, water meter, vortex, Alia Flow Meter, Floating Oil Skimmer, Hydraulic Breaker, Hydraulic Hammer, Precission Bearing, Quick die Change, Hydraulic dies clamp, Pneumatic Gear Motor, Air Motor, Oil cooler, Fan Blower, Axial Blower, Index units, Stepping Motor, Connector Harting, Connector Nanaboshi, Position gate, Portable Flow Meter, Ultrasonic sensor, ORIFICE, VORTEX, Diaphragm Pump, OVAL METER, SOLID FLOWMETER, POWDER SENSOR, LEVEL POWDER, KANSAI SENSOR, TOKICO, FC Korea, Etc.

II. WORKSHOP ( Improvement, Repair, Modification and Manufacture)

Jig & Fixtur, Dies Expander, Gear, Punch, Stamp Holder, Stamp Marking, Ejector Pin, ShearBalde, Cutting Angle, Isolator Hanger, Spot Pin, Mould, Taper Jig, Cones, Bushing, Cylinder Hydraulic, Pulley, Flange, Fitting, Shaft, Cam Slider, Shuttle Roller, Driven Roller, Bracket, etc .
Hard Chrome : Crank Shaft, Rod & Tube Hydraulic, Roll Met, Alumunium, Linner, Moulding, Dies, Shaft, Screw, Jig, Stainless Steel, Rel Guide, Beading Roll, Pin Core, aksesoris, etc

III. INSTALLATION, OVER HAUL, RECONDITION, MAINTENANCE
Mechanical Press MAchine, Hydraulic Press MAchine, Expander, Die Casting Machine, Forging Press, Roller, Sprue Cutting, Chiller, AC Central, Screw Compressor, Drill Multi Machine, Conveyor, Shot Blasting, Boiler, Gear Box, Pump, Hydrant.

IV. FABRICATION
Conveyor, Tank, Piping, Trolley, Rack, Conveyor, Canopy, Box, Table, Gate, dll
To achieve the company purpose, PT. WIRATAMA MITRA ABADI will always develop and expand cooperation with other party, through work mechanism which is supports eachother, and commitment to develop and to give satisfaction to costumers and our partners .
Website at www.wmablog.com

Perhatian !

Perusahaan ini terdaftar sebagai Free Member. Hindari melakukan pembayaran sebelum bertemu penjual atau melihat barang secara langsung. COD (Cash On Delivery) atau bertemu langsung dengan penjual merupakan metode transaksi aman yang kami sarankan.

Deskripsi Produk Deskripsi

Detail All Metal Digital MFC / MFM MODEL EX-550 SERIES

Features

Metal sealing design.
Lower cost but high accuracy measurement.
High speed response and zero stability.
0-5VDC or 4-20mA input/output signal and +/-15VDC or 24VDC power supply.
Mediocrity D-sub 9pin.
Gases registered in EX-550 are usable by rotary-switch.
*Calculate the flow rate with conversion factor based on N2 gas.
RoHS compliance, CE marked.

Stand Specifications

Model		Mass Flow Controller	Mass Flow Meter
		EX-550C	EX-550M
Sensor type		Thermal sensor
Valve type		Normally closed proportional solenoid valve	-
*Applicable gases（1）**		N2、Air、H2、He、Ar、O2、CO2 etc.
		(Gases not specifically mentioned here are subject to calibration for N2 equivalent.)
*Flow range（2）**		10SCCM ～ 5SLM
Control（measure）range		2 ～ 100%(F.S.)
Response		≤ 1sec （within ± 2%F.S.）（*4）
Accuracy		± 1.0%S.P. (25%F.S. ～ 100%F.S.) , ± 0.25%F.S. ( ～ 25%F.S.)
Repeatability		± 0.2%FS
*Operating differential pressure（3）**		50 ～ 300kPa（Ar、CO2：１00kPa ～ 300kPa）	-
Inlet maximum pressure		350kPa（G）
Proof pressure		980kPa（G）
External leak rate（He）		≤ 1.0 × 10-11Pa・m3/sec
Temperature	Working temp.	5 ～ 50℃
	Accuracy guaranteed temp.	15 ～ 35℃
	Allowable storage temp.	-10 ～ 60℃
Allowable operating humidity		10 ～ 90%RH（without dew condensation）
Materials of gas contact part		SUS316L、PTFE、Ni-Co
Electrical connection		Dsub 9pin KFC Standard（SEMI standard compliant）
		HR-10A × 2
Flow rate setting signal		0～5VDC(input impedance: approx. 1M Ω)	-
		or 4～20mA(input impedance: approx. 250 Ω)
Flow rate output signal		0 ～ 5VDC( load resistance ≧10k Ω)
		or 4 ～ 20mA( load resistance ≧500 Ω)
Digital communication		RS485　rotary-switch address setting
Required power supply (DC)		+15VDC( ± 5%)100mA , -15VDC（± 5%）150mA
		or +24VDC（± 10%） ≤180mA　 (MFM would be ≤100mA)
Joint		1/4VCR
Mounting posture		Free
Weight		Approx.800g	Approx.550g